Weston 650501W Use and Care Manual download pdf (Page 16)

REPLACING THE SEAL BAR TAPE:

1. Press the ON/OFF Button on the

Control Panel to turn the Vacuum Sealer

“OFF”.

2. Disconnect the Vacuum Sealer from the

power supply.

3. Make sure the Vacuum Sealer is

completely cool.

4. Pick at either end of the Seal Bar

Tape covering the Seal Bar Heating

Element until it lifts slightly (Figure 18).

Grasp the loose end and slowly pull

the Seal Bar Tape back over itself until fully

removed.

5. Remove the backing from a new strip of Seal Bar Tape. Be careful not to allow the

Seal Bar Tape to contact anything including itself while the adhesive side is exposed.

6. Hold one end of the Seal Bar Tape in each hand. Stick the left end of the Seal Bar

Tape to the at area on the Base just left of the Seal Bar Heating Element. Apply the

Seal Bar Tape from left to right over the Seal Bar Heating Element. Make sure there

are no wrinkles or folds in the Seal Bar Tape once applied. The Seal Bar Tape should

fully cover the Seal Bar Heating Element.

Figure 18

Seal Bar Tape

Seal Bar Heating

Element

6. Remove the Plastic Lid Base, 2

Release Buttons and the 2 Release

Springs from the Stainless Steel Lid.

7. To install the new Lid Assembly, turn

the Plastic Lid Base upside down with the

Vacuum Chamber Lid Seal positioned

towards the front of the Vacuum Sealer

and the Seal Bar Insulator facing you.

8. Place the 2 Release Buttons into the

slots (Figure 20). Insert the 2 Release

Springs into the backs of the Release

Buttons.

9. With the Vacuum Chamber Lid

Seal positioned towards the front of

the Vacuum Sealer and the Seal Bar

Insulator facing you, carefully position

the Plastic Lid Base Assembly back

onto the Stainless Steel Lid so that the

4 screw holes in the Plastic Lid Base

line up with the 4 screw posts on the

Stainless Steel Lid.

10. Use one hand to hold the Plastic Lid Base and the other to insert and turn the 4 Lid

Screws. HINT: It may work better to tilt the Vacuum Sealer on its side when installing

the Lid Screws.

11.When all 4 Lid Screws are installed, the Plastic Lid Base should be ush to the

Stainless Steel Lid. If it is not, then the Lid Screws may be improperly installed (i.e.

crooked or not tight enough).

Release Button

Figure 20

Release Spring

Plastic Lid Base

Stainless Steel Lid

Seal Bar Insulator

Screw

Posts

de l’aspiration/ du scellage (rampe VACUUM PROGRESS).

Appuyer sur la touche ON/OFF pour interrompre au besoin le processus.

9. NE PAS tenter d’ouvrir le couvercle avant la n de l’aspiration (risque

d’endommagement de l’appareil). Enfoncer les deux boutons déclencheurs du couvercle

(Figure 7) de chaque côté de la scelleuse pour libérer le verrou, puis ouvrir le couvercle.

10. Retirer le sac à vide scellé. Patienter au moins 20 secondes avant un autre scellage

pour que l’appareil ne surchauffe pas.

11. Appuyer sur la touche ON/OFF (Figure 6) du tableau de commande pour éteindre la

scelleuse.

12. Débrancher la scelleuse de la source d’alimentation avant de quitter les lieux lorsque

le travail est terminé.

REMARQUE: La scelleuse sous vide doit être utilisée UNIQUEMENT avec des SACS SOUS

VIDE. Pour obtenir les meilleurs résultats, utiliser uniquement les sacs sous vide recommandés.

NE PAS UTILISER DES SACS À USAGE DOMESTIQUE ! Toute utilisation contre-indiquée de

cette scelleuse sous vide risque d’endommager l’appareil et pourrait annuler la garantie !

-16- -29-

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 22

Comments to this Manuals

No comments

Weston 650501W Use and Care Manual Page 16

Comments to this Manuals

Related products and manuals for Vacuum sealers Weston 650501W